Wingback chair blue, tailor made
- Reference: OREILLE-BLEU-NAT
The width of the seat is equal to the width of your hips plus 2 to 5 cm. To measure it, sit on a flat surface, place two parallel blocks against your hips, measure the distance between them and add 2 to 5 cm.
To measure the depth of the seat, sit on a flat surface.
1. Measure the distance from the wall to the recess at the back of the knee.
2. Remove about 4 cm to get the seat depth measurement of the chair.
Correct measurement of the seat depth will result in better weight distribution over the entire seat, better blood circulation and therefore greater comfort.
It is important that the seat is not too deep so that it does not rest on the popliteal fossa at the back of the knee, which would hinder venous return.
To measure the height of the seat
1- Sit on a surface that is high enough so that your feet do not touch the floor.
1. Add books under the feet so that :
- the front of the thigh rests on the front of the seat (no hand should be able to pass through).
- the feet are no longer in the air
3. Measure the distance from the underside of the heel to the seat
If the seat is too high, the knees are up and the supports are more important at the bottom of the seat; the sitting position is quickly painful.
If it is too low, the feet are not on the floor and the user slides forward.
To measure the height of the backrest sit on a flat surface. You can choose between 3 types of backrest.
Classic backrest (Figure 1)
Pinch a pencil under the armpits and measure the height of the seat with the pencil.
Mid-high backrest (Figure 2)
Measure the height from the seat to the shoulder blades or base of the cervical vertebrae.
High backrest (Figure 3)
Measure the height from the seat to the rearmost part of the head.
Some benefits of our blue backwing tailor made chair
Made to measure, it allows you to sit comfortably all day long and to adopt a good posture for your back.
The benefits of a customised chair are :
. a customised height and depth of sitting allows, by distributing the support pressures harmoniously, to improve blood circulation; in this way, pain felt in the buttocks due to poor vascularisation in relation to the ischials is avoided
. a custom-made seating depth allows you to sit at the bottom of the chair, with your back resting against the backrest; the spine thus retains its natural curvature
. the seat does not rest against the calf so that the venous return is not slowed down
. a seat angle of 10° reinforces these benefits by making it easier for the back to rest against the backrest and reducing pressure on the seat
Bultex foams used for seat and back cushions have a high resilience, which means that they retain their original properties for a long time. Their relative thinness, compared to a traditional lounge chair, makes it easier to get up and avoid the hammock effect. For the chair to be comfortable for hours during this seat foam at a high density of 38 Kg/m3.
The backrest combines different foam densities, denser in the centre to form a lumbar support and on the sides for lateral support.
As an option it is possible to have a 1 cm layer of reception foam on top; it gives an impression of softness.
The chair structure consists of 4 MDF* panels with slots: they can be assembled without tools. The seat can be quickly dismantled for transport or storage in a reduced volume.
MDF panels are dyed in the mass: if a panel is damaged on its surface it can be sanded down to its original colour.
Why choose a blue armchair?
With the blue color you can create a refreshing and relaxing look. In the interior design, you can use blue to create an atmosphere of rest and meditation. The color blue has been shown to lower blood pressure and heart rate. It is used to design the interior space to enlarge the room by a very light shade of blue. You can use blue to cool a room with much sun and heat.
High resilience Bultex firm foam with a density of 40 Kg/m3. Thickness 50 mm. Bultex is a high quality foam for a lasting support.
Bultex high resilience PU foam 30 Kg/m3 thickness 50 mm for a lasting support and comfort
The angle of the seat is 9° (to the ground) and the angle of the backrest is 18° (to the vertical).
19 mm thick Valchromat panels, tinted with organic dyes. On the surface there are small pure wood fibres which have not absorbed the organic dyes.
3 layers of clear matt vitrifier - Ceramic Technology V33: high performance resin combined with ceramic microbeads, creating a shield and increasing strength by 40%.
Made in France from Valchromat panels made in Portugal. Precision cutting of the base to measure with a numerical control. Handcrafted finishing of the structure and cushions.
Delivery and assembly
Delivery flat-pack to reduce CO2 emission, in a wooden crate. The grooved panels can be assembled without tools (some accessories may require the use of a screwdriver for assembly).
Removable cover. Wash cushion and frame with mild detergent ( water and soap ).